Two-post in-ground lift with flat support bridge mount
Flat support bridge (FT) hot-dip galvanised:
Easier, tyre-preserving drive-on thanks to all-round bevelled pull-out elements combined with low construction height with rubber mounting plate (construction height no more than approx. 60 mm)
Large mounting areas thanks to interchangeable mounting plate system cover the entire vehicle spectrum
Flexible and optional range of mounting plates in versions ‘longer – wider – lower’ guarantee optimum mounting of all current and future vehicle models
Rubber support plate enables time-saving direct hold
Optional floor-level installation available for improved lifting platform mount drive-on
Pinch point protection thanks to CE stop rather than foot guard
Compact post-lifting unit provides excellent under-vehicle access and lighting.
Torsion-resistant square post ensures high rigidity and safety.
Quiet pump and motor with corrosion-proof oil-submerged design (bio-oil optional).
Electronic, contactless lift control with wear-free limit switches and error display.
Smooth operation via long-life nickel-coated posts and low-maintenance guide design.
Internal hydraulic safety cylinder for long service life.
Mobile synchronisation and safety yoke for balanced post guidance (standard).
Fast lifting/lowering speeds up to approx. 30/20 seconds.
Compatible with all MAHA installation boxes up to 5,500 kg.
Battery-powered emergency lowering included.
Optional ergonomic controls via traffic-light energy module or flush-mounted panel.
Flat support bridge hot-dip galvanized
Lift unit with movable yoke w Wiring and mounting material
Installation box/installation frame not included in delivery
Emergency DOWN cable for connection to switch box
Control unit with 2 x 10 m control cables (flexible oil cables)
Lockable master switch
Operating manual and test log w EC Declaration of Conformity CE
Load Capacity (CE): 3500 kg
Max Lifting Height: 1960 mm
Lengthways Holder (locking positions): 1400–2000 mm
Crosswise Holder (reconnected): 880–1820 mm
Support Plate Size (L × W): 355 × 400 mm
Raising / Lowering Time (approx., load-dependent): 30 s / 20 s
Installation Depth: 2382 mm
Piston Centres: 1350 mm
Post Dimensions: 180 mm (square)
Operating Pressure: 160 bar
Motor Power: 3 kW
Fuse: gG 16 A
Power Supply: 3/N/PE 400 V, 50 Hz
Control Unit Size (H × W × D): 320 × 220 × 120 mm
Hydraulic Fluid Required: 28 L (not included)
Two-post in-ground lift with flat support bridge mount
Flat support bridge (FT) hot-dip galvanised:
Easier, tyre-preserving drive-on thanks to all-round bevelled pull-out elements combined with low construction height with rubber mounting plate (construction height no more than approx. 60 mm)
Large mounting areas thanks to interchangeable mounting plate system cover the entire vehicle spectrum
Flexible and optional range of mounting plates in versions ‘longer – wider – lower’ guarantee optimum mounting of all current and future vehicle models
Rubber support plate enables time-saving direct hold
Optional floor-level installation available for improved lifting platform mount drive-on
Pinch point protection thanks to CE stop rather than foot guard
Compact post-lifting unit provides excellent under-vehicle access and lighting.
Torsion-resistant square post ensures high rigidity and safety.
Quiet pump and motor with corrosion-proof oil-submerged design (bio-oil optional).
Electronic, contactless lift control with wear-free limit switches and error display.
Smooth operation via long-life nickel-coated posts and low-maintenance guide design.
Internal hydraulic safety cylinder for long service life.
Mobile synchronisation and safety yoke for balanced post guidance (standard).
Fast lifting/lowering speeds up to approx. 30/20 seconds.
Compatible with all MAHA installation boxes up to 5,500 kg.
Battery-powered emergency lowering included.
Optional ergonomic controls via traffic-light energy module or flush-mounted panel.
Flat support bridge hot-dip galvanized
Lift unit with movable yoke w Wiring and mounting material
Installation box/installation frame not included in delivery
Emergency DOWN cable for connection to switch box
Control unit with 2 x 10 m control cables (flexible oil cables)
Lockable master switch
Operating manual and test log w EC Declaration of Conformity CE
Load Capacity (CE): 3500 kg
Max Lifting Height: 1960 mm
Lengthways Holder (locking positions): 1400–2000 mm
Crosswise Holder (reconnected): 880–1820 mm
Support Plate Size (L × W): 355 × 400 mm
Raising / Lowering Time (approx., load-dependent): 30 s / 20 s
Installation Depth: 2382 mm
Piston Centres: 1350 mm
Post Dimensions: 180 mm (square)
Operating Pressure: 160 bar
Motor Power: 3 kW
Fuse: gG 16 A
Power Supply: 3/N/PE 400 V, 50 Hz
Control Unit Size (H × W × D): 320 × 220 × 120 mm
Hydraulic Fluid Required: 28 L (not included)
