COMPLIANCE|MAINTENANCE|EQUIPMENT Response within one business day | 1300 871 711 | Customer Portal

Equipment / Oil Equipment & Accessories / Oil Meters & Control Valves / Graco Pulse metered dispense valve for antifreeze, 1/2 in NPT, flexible extension, antifreeze nozzle

Graco

Graco Pulse metered dispense valve for antifreeze, 1/2 in NPT, flexible extension, antifreeze nozzle

In most workshops, coolant is the last unmanaged fluid. Engine oil is pumped, metered and charged. Transmission fluid is on a reel. Coolant is in a drum in the corner with a jug beside it, and nobody knows how much of it went into anything. Graco’s Pulse metered dispense valve for antifreeze applications closes that gap: the technician dispenses a measured quantity, the volume is displayed to plus or minus 0.5 per cent, and the fluid can be charged and recorded like everything else.

Key features

  • Metered coolant and antifreeze dispensing to plus or minus 0.5 per cent
  • Flow range 0.25 to 18 gpm (0.9 to 68 lpm)
  • Rated to 1500 psi (103.4 bar) maximum working pressure
  • Supplied with an antifreeze nozzle, so the coolant line is never confused with the oil line
  • 1/2 in BSPP flexible, 1/2 in NPT flexible and 1/2 in NPT rigid extension options
  • Runs on four AA alkaline cells
  • Part of the Graco Pulse fluid management family, so the volume can be recorded, not just shown

Specifications

Maximum working pressure1500 psi (103.4 bar)
Flow range0.25 to 18 gpm (0.9 to 68 lpm)
Accuracy+/- 0.5 per cent
Inlet1/2-14 NPT or 3/4-14 NPT
Outlet3/4-16 straight thread o-ring boss
Length (without extension)13 in (33 cm)
Width3.75 in (9.5 cm)
Height5.75 in (14.6 cm)
Weight5.3 lb (2.4 kg)
Battery4 x AA alkaline
Operating temperature range4 to 158 F (-16 to 70 C)
Wetted partsAluminium, stainless steel, PBT, nitrile rubber, zinc-plated carbon steel, nickel-plated carbon steel
Fluid compatibilityAntifreeze, gear oil, crankcase oil, ATF, windscreen washer fluid
Environmental ratingPro indoor only; Mobile IP69K

Graco’s published accuracy figure is measured at 2.5 gpm (9.5 lpm) and 70 F (21 C) on 10-weight oil over a one-gallon dispense, and the flow range is tested in 10W motor oil. Both vary with pressure, temperature and viscosity, so the valve may require calibration on your coolant. We do that at commissioning.

Why coolant deserves its own dispense point

Three reasons, in order of how much money they represent. First, recovery: coolant is expensive, and the litres given away in un-metered top-ups are pure margin loss. Because each individual top-up feels trivial it is never questioned, and over a year it is significant. Second, accuracy: modern cooling systems are not forgiving of the wrong concentration, and a measured dispense is the only way to get a repeatable mix. Third, contamination: a dedicated coolant line and valve means the jug that was used for coolant is not the jug that ends up holding something else.

Do not dispense coolant through an oil valve

Glycol-based coolants attack seals and materials chosen for petroleum oils, and they crystallise as they dry, which is hard on moving parts in a meter. A valve specified for antifreeze is built for that service, and Graco lists antifreeze in this valve’s published fluid compatibility. Running coolant through a valve that is not rated for it appears to work for a while and then does not, usually taking the meter accuracy with it before it fails outright. The antifreeze nozzle also stops the coolant line and the oil line ever being confused at the point of use.

Where the valve fits in the installation

A coolant dispense point needs a pump suited to the fluid, its own reticulation or reel, and a valve rated for glycol. The most common upgrade path in an existing workshop is to add a dedicated coolant pump and reel to the bulk store already in place, then fit the metered valve at the bay. If used coolant is also being collected, a separate antifreeze receiver keeps it out of the used oil tank, which protects the value of your used oil.

Installed and serviced by TWSA

TWSA quotes coolant dispensing as part of the whole fluid installation, because the pump, the line, the reel and the valve have to agree with each other. Tell us which coolants you stock, whether they are supplied concentrated or pre-mixed, and how many bays need access, and we will specify the dispense points and quote the installation. Our technicians install and commission the valve, calibrate it on your coolant and keep it on a service cycle afterwards.

Specification

TWSA part numberT-25M320
DescriptionPulse metered dispense valve for antifreeze, 1/2 in NPT, flexible extension, antifreeze nozzle

Part of the Graco Antifreeze Control Valves range. Supply, installation and servicing are quoted to suit your site.

Get this quoted for your workshop

No prices on the site, on purpose. The Graco Pulse metered dispense valve for antifreeze, 1/2 in NPT, flexible extension, antifreeze nozzle is quoted with supply, installation and servicing scoped to your bays and workload.

Building a list? Add several items and send them as one request.

Quote this item on its own Response within one business day, from a technician.

Prefer to talk it through?
1300 871 711

← Back to Oil Meters & Control Valves

Supported after the sale

We install it, commission it and keep it compliant

Everything TWSA supplies is backed by our own technicians and a documented service record from day one.

Request a Quote Call 1300 871 711
Call 1300 871 711 Get a Quote