Workshop Compliance|Maintenance|Equipment Response within one business day | 1300 871 711 | Customer Portal

Equipment / Automotive Workshop Equipment / Fume & Exhaust Extraction / Filcar Extraction Fans, Arms & Filtration Units

Filcar

Filcar Extraction Fans, Arms & Filtration Units

Behind every extraction hose there is a fan, and in front of some of them there needs to be a filter. This page covers the fans that move the air, the articulated arm that captures welding and grinding fume where there is no tailpipe to clip onto, and the filtration units for the contaminants that must not simply be blown outside.

Ordering table

ModelConfiguration
AM-TXExtraction fan, configuration confirmed on quotation
MICRO-TXCompact extraction fan, configuration confirmed on quotation
BL-A-TXExtraction fan, BL-A-TX configuration
ARMTELArticulated extraction arm
FCPFiltration unit
FCP DRWFiltration unit, DRW configuration
Technical cabinets for exhaust extractionEnclosure for extraction plant and components

Sizing the fan to the system, not to the bay

Fan selection is the part of an extraction system most often guessed at. Two numbers drive it: the air volume needed at each capture point, and the static pressure the fan must develop to overcome the resistance of the hose, the duct, the bends and the filter. Both go up as you add bays, lengthen the run or reduce the duct diameter.

A compact fan such as the MICRO-TX suits a single capture point on a short run: one bay, one hose, discharge close by. The AM-TX and BL-A-TX fans are the choices as the system grows, either because more capture points run at once or because the duct run to the discharge is long or convoluted. The mistake to avoid is specifying a fan for the number of bays without accounting for the run: a single bay at the far end of a long ducted run can be more demanding than two bays next to the discharge point.

Simultaneity is the other input. A system serving eight drops where two run at once is a different fan to a system where all eight run at once. We ask how you actually work rather than counting bays.

ARMTEL: capture where there is no tailpipe

An articulated extraction arm is for the fume that is generated at a point rather than emitted from a pipe: welding, brazing, grinding and soldering. The arm positions a hood within a short distance of the arc or the work, holds that position, and captures the plume before it reaches the welder breathing zone.

This is a serious exposure control. Welding fume contains metal oxides and, depending on the process and the consumable, may contain hexavalent chromium, manganese and nickel compounds. Welding fume generally is now treated as carcinogenic to humans, and workplace exposure standards apply to the individual constituents. In Australia, a workshop that welds regularly is expected to control fume at the source. A fixed or bench mounted articulated arm is the standard engineering control for that, and it is preferred over relying on respiratory protection alone.

FCP filtration: when discharge outside is not enough

Ducting to atmosphere is the right approach for engine exhaust. It is not always the right approach for welding and grinding fume, dusts and oil mist, where the contaminant may need to be captured on a filter before the air is discharged, or where the air needs to be recirculated because the building cannot lose that much conditioned air. FCP and FCP DRW filtration units serve those applications.

Filtration also protects the fan and the duct. Sticky, oily or particulate laden air will progressively coat a duct interior, which reduces its diameter, raises the static pressure and quietly degrades capture until nobody trusts the system. Where the contaminant is particulate, a filter is cheaper than periodic duct cleaning.

Technical cabinets

The technical cabinets for exhaust extraction give the plant, controls and components a proper enclosure rather than leaving them exposed on a workshop wall. In a busy workshop that means fewer knocks, less dust ingress, and a tidier installation that is easier to service.

Designed, installed and commissioned

Fans, arms and filters only work as a matched system with correctly sized ductwork. TWSA designs the system against your bay count, vehicle types, welding activity and building constraints, installs it and commissions it so capture is verified. Tell us what you do and where, and we will quote it.

Get this quoted for your workshop

No prices on the site, on purpose. The Filcar Extraction Fans, Arms & Filtration Units is quoted with supply, installation and servicing scoped to your bays and workload.

Building a list? Add several items and send them as one request.

Quote this item on its own Product sheet · 1 page (PDF) Full brochure · specifications (PDF) Response within one business day, from a technician.

Prefer to talk it through?
1300 871 711

← Back to Fume & Exhaust Extraction

Supported after the sale

We install it, commission it and keep it compliant

Everything TWSA supplies is backed by our own technicians and a documented service record from day one.

Request a Quote Call 1300 871 711
Call 1300 871 711 Get a Quote